BLACK FRIDAYJahrestiefstpreise
HOHE RABATTGUTSCHEINENur für kurze Zeit
00Tage10Std37Min12Sek
Jetzt kaufen
LiThink

Black-Friday-Angebot

Zusätzlich sichern
6 % Rabatt

Dein Black-Friday-Vorteil

03Stunden 00Minuten 00Sekunden

Sichere dir deinen Black-Friday-Rabatt.
Abonnieren und 6 %-Rabattcode freischalten.

In-Depth Analysis: Temperature Behavior of LiFePO4 Batteries

Tiefgehende Analyse: Temperaturverhalten von LiFePO4-Batterien

How Temperature Affects Capacity, Internal Resistance and Voltage

LiFePO4 batteries are one of today's leading battery technologies, and their performance is closely linked to temperature. Whether in marine engines, motorhomes or solar systems, temperature affects their capacity, internal resistance and voltage in various ways.

Today, we take a detailed look at the temperature behaviour of lithium iron phosphate batteries using three samples and provide practical recommendations for optimal operation.

1. Effect of Temperature on Battery Capacity

Sample 1: 3.2V/11Ah Battery

Chart: Battery capacity increases with temperature from minus 40 to 60 degrees Celsius

At low temperatures, battery capacity drops extremely quickly, while it increases more slowly at temperatures above room temperature. At -40°C the capacity is only about one third of the rated value. Between 0°C and 60°C the capacity rises from 80% to 110% of rated capacity.

Sample 2: 3.2V/10Ah Battery

Critical transition points in the low-temperature range:

  • At 0°C: 80,2% of capacity at room temperature
  • At -10°C: Reduced to 66,4% reduziert
  • At -20°C: Only 44,1% remaining

Key findings:

• The rate of decrease at -20°C (15,6%) is twice as high as at -15°C (7,3%) - therefore, -20°C is considered a critical threshold for LiFePO4 batteries.

• Charging and discharging capacity increases by only 10 percent at room temperature.

• Above 50°C capacity decreases again - at 60°C it equals the capacity at room temperature.

Sample 3: 3.2V/20Ah Power Battery

After 20 hours of storage at various temperatures and discharge at 0,3C:

Chart: Capacity as a percentage in relation to temperature

  • At -20°C: Only 55% of capacity at room temperature
  • At 55°C: Slight increase in capacity compared with 25°C

Optimal Operating Temperature

Based on data from all samples: 0°C to 50°C is the optimal temperature range for maximum capacity and longevity.

Effect of Temperature on Capacity - Summary

Temperature Range Capacity Behaviour Recommendation
< -20°C Extreme capacity loss (<50%) Avoid
-20°C to 0°C Significant capacity loss (44-80%) Use heating
0°C to 25°C Slight increase (80-100%) Ideal
25°C to 50°C Maximum capacity (100-110%) Optimal
> 50°C Capacity decrease Cooling required

2. Effect of Temperature on Internal Resistance

Sample 1: 3.2V/11Ah Battery    Chart: Ohmic charging internal resistance by state of charge at 10, 25 and 40 degrees CelsiusBattery charging ohmic internal resistance curves for each SOC value at three temperatures  
Chart: Polarisation charging internal resistance by state of charge at 10, 25 and 40 degrees Celsius Battery charging polarisation internal resistance curves for each SOC value at three temperatures
Chart: Total charging internal resistance by state of charge at 10, 25 and 40 degrees Celsius Battery charging total internal resistance curves for each SOC value at three temperatures
Chart: Ohmic discharging internal resistance by state of charge at 10, 25 and 40 degrees CelsiusBattery discharging ohmic internal resistance curves for each SOC value at three temperatures
Chart: Polarisation discharging internal resistance by state of charge at 10, 25 and 40 degrees CelsiusCell discharging polarisation internal resistance curves for each SOC value at three temperatures
Chart: Total discharging internal resistance by state of charge at 10, 25 and 40 degrees CelsiusBattery discharging total internal resistance curves for each SOC value at three temperatures

• Internal resistance remains stable at a constant temperature across a wide SOC range (0,3-1,0)

• At low SOC (<0,1), resistance rises dramatically

• Polarisation resistance rises faster than ohmic resistance

As temperature decreases, both ohmic and polarisation resistance increase. However, ohmic resistance is more sensitive to temperature because it depends primarily on the ionic conductivity of the electrolyte, which decreases in the cold.

• The change in resistance is more pronounced at low temperatures

• At 25°C, the behaviour is more similar to that at 40°C than at 10°C

• The lower the temperature, the more sharply resistance rises as SOC decreases

Sample 2: Square 3.2V/40Ah Battery

• Ohmic resistance rises more sharply than polarisation resistance as temperature decreases

• Below 0°C, total resistance increases significantly more

• At temperatures above 0°C, ohmic resistance is independent of SOC

Key Finding: Resistance Composition

Ohmic resistance dominates total resistance and can account for up to 92,13% of it. Reducing ohmic resistance is therefore crucial to reducing heat generation.

Internal Resistance and Temperature - Summary

Parameter Effect of Temperature Practical Implication
Ohmic Resistance Highest temperature sensitivity Main cause of heat generation
Polarisation Resistance Lower temperature sensitivity Rises earlier at low SOC
Total Resistance Rises exponentially in the cold Critical below -5°C
Optimal SOC Range 0,2-0,8 for stable resistance Maintain for best performance

3. Effect of Temperature on Open-Circuit Voltage (OCV)

Sample 1: 3.2V/11Ah Battery

The open-circuit voltage (OCV) of LiFePO4 batteries rises as SOC increases, but remains relatively flat in the middle SOC range (0,3-1,0). Below an SOC of 0,3, voltage drops sharply.

• The OCV curves for charging and discharging differ slightly

• After a rest period, voltage approaches the actual OCV value

• Lower temperatures generally result in lower OCV curves

Thermodynamic Principles

OCV is determined by the Nernst equation and depends on the standard EMF, thermodynamic temperature and reactant concentrations. In the range of 10-40°C OCV differences are minimal.

OCV and Temperature - Summary

Factor Effect on OCV Remarks
Temperature (10-40°C) Low Differences are often negligible
SOC Main determining factor Stable in the middle range (0,3-0,8)
Temperature <10°C More pronounced effect Differences increase
Charge/Discharge History Minor differences Can be offset by relaxation

Summary & Recommendations

Key Findings from the Analysis

1. Optimal Temperature Range: 0°C to 50°C

2. Effect of Cold:

  • -20°C is the critical point for drastic performance losses
  • Significant capacity loss and sharply increased internal resistance

3. Effect of Heat:

  • Above 50°C can lead to capacity loss over time

4. Internal Resistance:

  • Ohmic resistance is the most temperature-sensitive
  • Resistance rises sharply at low temperatures and low SOC
  • Keep SOC between 0,2 and 0,8 for efficient operation

5. Open-Circuit Voltage (OCV):

  • Primarily determined by SOC
  • Most stable in the middle SOC range
  • Temperature has only a minor effect (10-40°C)

Practical Recommendations for Users

  • Use temperature management systems (heating/cooling) in extreme environments
  • Avoid deep discharge especially at low temperatures
  • Keep the SOC between 20% and 80% for optimal performance
  • Monitor battery temperature in real time in demanding applications
  • Allow batteries to rest sufficiently after charging/discharging to obtain accurate OCV measurements

LiFePO4 batteries offer excellent performance for propulsion and energy storage applications thanks to their high level of safety and long service life. Understanding their temperature characteristics enables scientifically informed handling that extends service life and improves efficiency.

1 comment

  • DINDA AULIA AZZAHRA PUTRI PURWANTO
    • DINDA AULIA AZZAHRA PUTRI PURWANTO
    • July 12, 2026 at 3:54 am

    Analysis of LiFePO4 battery performance indicates that temperatures outside the 0°C to 50°C range significantly affect capacity, with temperatures below -20°C representing a critical threshold that causes a drastic drop to under 50%. As an Electrical Engineering student at Telkom University Surabaya, you can appreciate the importance of thermal management systems—such as heaters or active cooling—in maintaining battery operation within the optimal zone, thereby ensuring power system reliability across various field applications. https://bee-sby.telkomuniversity.ac.id/

Leave a comment

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.